Identification and Mitigation of Machining Process Failures in XE 611 SZK Crankshaft through an Integrated FMEA and Pareto Analysis Approach

Ichlas Nur; Rifki  Abdul Dhohir; Nasirwan; Nusyirwan4; Yuli Yetri

doi:10.52158/jamere.v6i2.1650

Penulis

Ichlas Nur Politeknik Negeri Padang
Rifki Abdul Dhohir Politeknik Negeri Padang
Nasirwan Politeknik Negeri Padang
Nusyirwan4 Politeknik Negeri Padang
Yuli Yetri Politeknik Negeri Padang

DOI:

https://doi.org/10.52158/jamere.v6i2.1650

Kata Kunci:

machining, milling, drilling, process failure, product quality

Abstrak

The quality of the machining process in critical components such as crankshafts plays a significant role in determining engine performance and reliability. This study aims to analyze the causes of failure in the milling and drilling machining processes of the XE 611 SZK crankshaft. The research methods included direct observation of the production process, analysis of machining parameters, and evaluation of machining quality through visual inspection and dimensional measurements. In addition, root cause analysis was conducted using fishbone diagrams and Failure Mode and Effects Analysis (FMEA) to identify the dominant factors contributing to process failures. Furthermore, Pareto analysis was applied to determine the primary causes of failure based on the 80/20 principle. The results indicate that machining failures were mainly caused by tool wear, improper cutting parameters (cutting speed, feed rate, and depth of cut), machine setup errors, and suboptimal coolant system performance. These failures resulted in surface defects, dimensional deviations, and an increased product rejection rate. The proposed recommendations include optimization of machining parameters, implementation of preventive maintenance for machines and tooling, and enhancement of quality control during the production process. This study is expected to serve as a reference for improving machining efficiency and reducing failure rates in the manufacturing industry

Referensi

1) Ade Riyan Hidayat, “Analysis of CNC Milling Machine Maintenance Time Optimization Using the Value Stream Mapping Approach and Improvements through Failure Mode and Effect Analysis on CNC Milling Machines,” Jurnal Rekayasa Mesin, vol. 18, no. 3, pp. 345–354, 2023.

2) Yeetu Yadav, Tanuj Kumar Gupta, Crankshaft Design and Fatigue Analysis for Enhanced Internal Combustion Engine Performance: A Review:,Journal of Advancements in Material Engineering, 2025

3) S. Wojciechowski J. Krajewska-Śpiewak, R.W. Marudac, G.M. Krolczyk, P. Nieslony, M. Wieczorowski , J. Gawlik, (2023), Study on ploughing phenomena in tool flank face – workpiece interface including tool wear effect during ball-end milling, Tribology International Volume 181.

4) I.A Choudhury, M.A El-Baradie, Machinability of nickel-base super alloys: a general review, Journal of Materials Processing Technology Volume 77, Issues 1–3, 1 May 1998, pp. 278-284

5) H. Sriwindiarto, “Analysis of Jig Design for Machining Base Crankshaft Pulley Puller on CNC Milling Machines Using the FMEA and FTA Methods at PT. XYZ,” G-Tech: Jurnal Teknologi Terapan, vol. 7, no. 4, 2023. doi:10.33379/gtech.v7i4.3314.

6) J. D. Rigden, A capacitive bore gauge, J Phys E, vol. 10, no. 12, pp. 1276–1278, Dec. 1977, http://dx. doi: 10.1088/0022-3735/10/12/024.

7) Gupta, K.K. and Jain, S. (2014) A Novel Multilevel Inverter Based on Switched DC Sources. IEEE Transactions on Industrial Electronics, 61, 3269-3278. http://dx.doi.org/10.1109/TIE.2013.2282606

8) Bai, S. Z., Hu, Y. P., Zhang, H. L., Zhou, S. W., Jia, Y. J., & Li, G. X. (2012).

Failure analysis of commercial vehicle crankshaft: A case study. Applied Mechanics and Materials, 192, 78–82

9) Fonte, M. A., Infante, V., Freitas, M. J., & Reis, L. (2016).

Failure mode analysis of two diesel engine crankshafts. Procedia Structural Integrity, 1, 313–318.

10) Witek, L., Stachowicz, F., & Załęski, A. (2017)., Failure investigation of the crankshaft of diesel engine. Procedia Structural Integrity, 5, 369–376.

11) Aliakbari, K. (2018). Analysis of the crankshaft failure of wheel loader diesel engine. International Journal of Engineering, 31(3), 473–479.

12) Alfares, M., Falah, A. H., & Elkholy, A. H. (2007). Failure analysis of a vehicle engine crankshaft. Journal of Failure Analysis and Prevention, 7(1), 12–17.

13) Hoten, H. V., (2013), Analisa Kegagalan Proses Face Milling Crank Case Pada Rotary Milling Machine, Teknosia vol.2, no.13

14) Sriwindiarto, H., Analisis Perancangan Jig Machining Base Crankshaft Pulley Puller pada Mesin CNC Milling dengan Metode FMEA dan FTA di PT. XYZ, G-Tech: Jurnal Teknologi TerapanVolume7, No. 4, 2023, hal. 1653-1662

15) Alain Sergent, Minh-Hien Bui, Hugues Favreliere, Daniel Duret, Serge Samper, François Villeneuve, Identification of machining defects by Small Displacement Torsor and form parameterization method, Proceedings of IDMME - Virtual Concept 2010 Bordeaux, France, October 2010 (2010) 1-6q.