MIXER DESIGN EQUIPPED WITH HEATING CONTROL ELEMENTS FOR MANUFACTURING COMPOSITE MATERIALS

  • Rifki Hidayat Aerospace Engineering Program, Sekolah Tinggi Teknologi Kedirgantaraan Yogyakarta
  • Erwhin Irawan Aerospace Engineering Program, Sekolah Tinggi Teknologi Kedirgantaraan Yogyakarta
  • Erwan Eko Prasetiyo Aerospace Engineering Program, Sekolah Tinggi Teknologi Kedirgantaraan Yogyakarta
  • Fery Setiawan Aerospace Engineering Program, Sekolah Tinggi Teknologi Kedirgantaraan Yogyakarta
DOI: https://doi.org/10.52158/jamere.v2i2.408
I will put the dimension here
Keywords: Mixer, mixing, stirring, temperature, heating element, white spot

Abstract

Composite is a composite material consisting of two or more materials with different mechanical properties. Composite materials are mixed to obtain new materials that have better micro-mechanical properties. To facilitate the mixing of composite materials and obtain materials that have good quality, in this study, a mixer machine design with heating elements was carried out so that the temperature could be adjusted as needed. Experiments from the results of a mixer machine with a heating element that have been made are comparing the mixing of resin and iron sand using a mixer machine without a heating element and using a heating element. The result of mixing composite materials using a mixer machine without heating elements is that the composite material is homogeneously mixed but when viewed from the micro-photos there are still many white spots so that the quality of the composite material is still not good. then the composite material is mixed and mixed using a mixer machine with a heating element, the composite material is homogeneously mixed and after seeing from the micro-photos there are a few wite spots on the composite.

References

A. Sabuin, K. Boimau, and D. G. H. Adoe, “Pengaruh Temperatur Pengovenan terhadap Sifat Mekanik Komposit Hibrid Polyester Berpenguat Serat Glass dan Serat Daun Gewang,” vol. 02, no. 01, pp. 69–78, 2015.

A. A. R. Wahid, “PERANCANGAN DAN PEMBUATAN ALAT PENGADUK SEMEN DALAM KODISI DARURAT / BENCANA DENGAN PENGGERAK MOTOR RODA DUA,” vol. 2507, no. February, pp. 1–9, 2020.

Moh Khairul Anam, “Rancang Bangun Mesin Mixer Untuk Pengaduk Bahan Crucible Berbahan Limbah Evaporation Boats,” Ranc. Bangun Mesin Mix. Untuk Pengaduk Bahan Crucib. Berbahan Limbah Evaporation Boats, 2020.

J. Suprianto, “REENGINEERING UNTUK MENINGKATKAN PRESTASI KERJA MESIN MIXER BATAKO,” p. 9, 2016.

S. E. Perangin-angin, A. Hamsi, Mahadi, Tugiman, D. Sitompul, and Indra, “Edisi Cetak Jurnal Dinamis , Desember 2015 ( ISSN : 0216-7492 ) Edisi Cetak Jurnal Dinamis , Desember 2015 ( ISSN : 0216-7492 ),” no. 4, pp. 1–14, 2015.

H. Lubis, A. Fathir, and Abas, “RANCANG BANGUN ALAT PENGGONGSENG KELAPA UNTUK PEMBUATAN BUMBU DAPUR DENGAN MENGGUNAKAN PEMANAS LISTRIK TEMPERATUR 800C DENGAN KAPASITAS 3 KG,” 2016.

Published
2022-08-03
How to Cite
Hidayat, R., Erwhin Irawan, Erwan Eko Prasetiyo, & Fery Setiawan. (2022). MIXER DESIGN EQUIPPED WITH HEATING CONTROL ELEMENTS FOR MANUFACTURING COMPOSITE MATERIALS. Journal of Applied Mechanical Engineering and Renewable Energy, 2(2), 52-61. https://doi.org/10.52158/jamere.v2i2.408
Section
Articles